GSE Logo - Home

0 Items $0.00

    You are here

    • You are here:
    • Home > Support > Glossary beginning with C

 

Supported Device List
Glossary Index

C

CAN bus

A controller area network (CAN bus) is a vehicle bus standard designed to allow microcontrollers and devices to communicate with each other in applications without a host computer. It is a message-based protocol, designed originally for automotive applications, but is also used in many other contexts. CAN bus is one of five protocols used in the on-board diagnostics (OBD)-II vehicle diagnostics standard. The OBD-II standard has been mandatory for all cars and light trucks sold in the United States since 1996, and the EOBD standard has been mandatory for all petrol vehicles sold in the European Union since 2001 and all diesel vehicles since 2004.

View Source: https://en.wikipedia.org/wiki/CAN_bus

CANbus

A controller area network (CAN bus) is a vehicle bus standard designed to allow microcontrollers and devices to communicate with each other in applications without a host computer. It is a message-based protocol, designed originally for automotive applications, but is also used in many other contexts. CAN bus is one of five protocols used in the on-board diagnostics (OBD)-II vehicle diagnostics standard. The OBD-II standard has been mandatory for all cars and light trucks sold in the United States since 1996, and the EOBD standard has been mandatory for all petrol vehicles sold in the European Union since 2001 and all diesel vehicles since 2004.

View Source: https://en.wikipedia.org/wiki/CAN_bus

Cartography

The art and science of graphically representing a geographical area, usually on a flat surface such as a map or chart; it may involve the superimposition of political, cultural, or other nongeographical divisions onto the representation of a geographical area.

View Source: http://www.britannica.com/EBchecked/topic/97492/cartography

CEP

Circular Error Probability or CEP is defined as the radius of a circle centered on the true value that contains 50% of the actual GPS measurements. So a receiver with 1 meter CEP accuracy will be within one meter of the true measurement 50% of the time. The other 50% of the time the measurement will be in error by more than one meter.

View Source: https://en.wikipedia.org/wiki/Circular_error_probable

Chipset

In a computer system, a chipset is a set of electronic components in an integrated circuit that manages the data flow between the processor, memory and peripherals. It is usually found on the motherboard. Chipsets are usually designed to work with a specific family of microprocessors. Because it controls communications between the processor and external devices, the chipset plays a crucial role in determining system performance.

View Source: https://en.wikipedia.org/wiki/Chipset

CNR

In telecommunications, the carrier-to-noise ratio, often written CNR or C/N, is the signal-to-noise ratio (SNR) of a modulated signal. The term is used to distinguish the CNR of the radio frequency passband signal from the SNR of an analogue base band message signal after demodulation, for example an audio frequency analogue message signal. If this distinction is not necessary, the term SNR is often used instead of CNR, with the same definition. High C/N ratios provide good quality of reception, for example low bit error rate (BER) of a digital message signal, or high SNR of an analogue message signal.

View Source: https://en.wikipedia.org/wiki/Carrier-to-noise_ratio

CoAP

Constrained Application Protocol (CoAP) is a software protocol intended to be used in very simple electronics devices that allows them to communicate interactively over the Internet. It is particularly targeted for small low power sensors, switches, valves and similar components that need to be controlled or supervised remotely, through standard Internet networks. CoAP is an application layer protocol that is intended for use in resource-constrained internet devices, such as WSN nodes. CoAP is designed to easily translate to HTTP for simplified integration with the web, while also meeting specialized requirements such as multicast support, very low overhead, and simplicity. Multicast, low overhead, and simplicity are extremely important for Internet of Things (IoT) and Machine-to-Machine (M2M) devices, which tend to be deeply embedded and have much less memory and power supply than traditional internet devices have. Therefore, efficiency is very important. CoAP can run on most devices that support UDP or a UDP analogue.

View Source: https://en.wikipedia.org/wiki/Constrained_Application_Protocol

C‐band

The C band is a name given to certain portions of the electromagnetic spectrum, including wavelengths of microwaves that are used for long-distance radio telecommunications. The IEEE C-band (4 to 8 GHz) and its slight variations contain frequency ranges that are used for many satellite communications transmissions, some Wi-Fi devices, some cordless telephones, and some weather radar systems. For satellite communications, the microwave frequencies of the C-band perform better under adverse weather conditions in comparison with the Ku band (11.2 GHz to 14.5 GHz) microwave frequencies used by other communication satellites.

View Source: https://en.wikipedia.org/wiki/C_band

Questions?

Have any questions?

We understand there are problems that cannot be solved by a product-in-a-box. If you have special requirements for your project, please contact us and we will provide you with a custom solution tailor-fit to your needs.